LAN settings

Change wireless/wired

Activates either wireless LAN or wired LAN. You can also deactivate wireless/wired LAN.
Wireless LAN setup

Selects the setup method for wireless LAN connection.

Note
- You can also enter this setting menu by selecting Wireless LAN setup on the HOME screen. In this case, activate wireless LAN.
When this menu is selected, the machine starts searching for a WPS-compatible access point. If the machine detects the access point, follow the on-screen instructions to set up wireless LAN. If an access point is not detected or if you select another setup method, select one of the setup methods below.
- Standard setup
  
  Select when you perform settings for wireless LAN manually using the operation panel of the machine.
- WPS
  
  Select when you perform settings for wireless LAN using Wi-Fi Protected Setup (WPS). Select Push button method or PIN code method according to the method your access point supports, then follow the on-screen instructions.
- Other setup
  
  Select Advanced setup if you perform settings by entering the access point's settings directly on the machine. Select Cableless setup if you specify the settings of the access point information to the machine directly from a device (such as a smartphone) without operating the access point. Follow the on-screen instructions of the connecting device for the setup procedure.

Confirm LAN settings

The list of wireless LAN settings of this machine is displayed on the touch screen. You can print the list from this setting menu.

WLAN setting list

The list of wireless LAN settings of this machine is displayed on the touch screen.

The following setting items are displayed.

Items	Setting
Connection	Active/Inactive
SSID	XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX
Communication mode	Infrastructure
Channel	XX
Wireless LAN security	Inactive/WEP(64bit)/WEP(128bit)/WPA-PSK(TKIP)/WPA-PSK(AES)/WPA2-PSK(TKIP)/WPA2-PSK(AES)
IPv4 address	XXX. XXX. XXX. XXX
IPv4 subnet mask	XXX. XXX. XXX. XXX
IPv4 default gateway	XXX. XXX. XXX. XXX
IPv6 address	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX
IPv6 subnet prefix length	XXX
IPv6 default gateway	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX
MAC address	XX:XX:XX:XX:XX:XX
IPsec settings	Enable (ESP)/Enable (ESP & AH)/Enable (AH)/Disable
Pre-shared key	XXXXXXXXXXXXXXXX
Printer name	XXXXXXXXXXXXXXX
Bonjour service name	XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX

("XX" represents alphanumeric characters.)

LAN setting list

The list of wired LAN settings of this machine is displayed on the touch screen.

The following setting items are displayed.

Items	Setting
Connection	Active/Inactive
IPv4 address	XXX. XXX. XXX. XXX
IPv4 subnet mask	XXX. XXX. XXX. XXX
IPv4 default gateway	XXX. XXX. XXX. XXX
IPv6 address	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX
IPv6 subnet prefix length	XXX
IPv6 default gateway	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX
MAC address	XX:XX:XX:XX:XX:XX
IPsec settings	Enable (ESP)/Enable (ESP & AH)/Enable (AH)/Disable
Pre-shared key	XXXXXXXXXXXXXXXX
Printer name	XXXXXXXXXXXXXXX
Bonjour service name	XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX

("XX" represents alphanumeric characters.)

Print LAN details

You can print out the network settings of the machine such as its IP address and SSID.

For more information on the machine's network setting is printed out:

Printing Out Network Setting Information

Important
- This printout contains valuable information about your computer. Handle it with care.

Other settings
- Set printer name
  
  Specifies the printer name. You can use up to 15 characters for the name.
  
  Note
  - You cannot change this setting with the memory card inserted in the card slot.
  - You cannot use the same printer name as that already used for other LAN connected devices.
  - You cannot use a hyphen for the initial or last character of the printer name.
- TCP/IP settings
  
  Performs IPv4 or IPv6 setting.
- Set memory card sharing
  
  Selects whether to share the card slot with a LAN connected computer.
  
  Note
  - You cannot change this setting with the memory card inserted in the card slot.
- WSD setting
  
  Setting items when you use WSD (one of the network protocols supported in Windows 8, Windows 7, and Windows Vista).
  Enable/disable WSD
  
  Selects whether WSD is enabled or disabled.
  
  Note
  - When this setting is activated, the printer icon is displayed on the Network Explorer in Windows 8, Windows 7 and Windows Vista.
  WSD scan from this device
  
  Selecting Enable allows you to transfer the scanned data to the computer using WSD.
  
  Timeout setting
  
  Specifies the timeout length.
- Bonjour settings
  
  Setting items for LAN using Bonjour for Mac OS.
  
  Enable/disable Bonjour
  
  Selecting Enable allows you to use Bonjour to perform the network settings.
  
  Service name
  
  Specifies the Bonjour service name. You can use up to 48 characters for the name.
  
  Note
  - You cannot use the same service name as that already used for other LAN connected devices.
- LPR protocol setting
  
  Activates/deactivates the LPR setting.
- PictBridge communication
  
  Setting items for printing from a PictBridge (Wireless LAN) compliant device.
  
  Enable/disable communication
  
  Selecting Enable allows you to print from a PictBridge (Wireless LAN) compliant device.
  
  Timeout setting
  
  Specifies the timeout length.
- Wireless LAN DRX setting
  
  Selecting Enable allows you to activate discontinuous reception when using wireless LAN. It allows you to save electricity.
  
  Note
  - Depending on the access point you are using, discontinuous reception may not be activated even though Enable is selected.
  - Discontinuous reception is activated only while the machine is on standby. (The touch screen is in the screen saver mode.)
- Wired LAN DRX setting
  
  Selecting Enable allows you to activate discontinuous reception when the machine is connected to a device compatible with wired LAN. It allows you to save electricity.
- Access point mode settings
  
  When you use the machine as an access point, specify the access point name and the security setting.
  
  Before Using the Machine with the Access Point Mode