skip to main text

Performing/Changing Wireless LAN Settings

Follow the procedure below to perform/change wireless LAN settings.

Important

  • Enable Easy wireless connect (Cableless setup) before performing printer setup. (Not required if you change the IP address.) For details, search for "NR049" on your printer's online manual and see the page shown.

Note

  • For some models, you can perform network setup for a USB connected printer using IJ Network Device Setup Utility. Select USB on Switch View under the View menu to display printers.
  1. Start up IJ Network Device Setup Utility.

  2. Check the displayed message and select Yes.

  3. Select Printer Network Setup on the displayed screen.

    Detected printers are listed.

  4. Select printer to perform/change settings from printer list.

    Select the printer with Wireless LAN displayed on Connection Method and the setting other than Unknown or Setup Completed displayed on Status to perform settings.

    To perform setup for a USB connected printer, select USB from the pulldown menu on the toolbar and select the printer with Wireless LAN displayed on Connection Method.

  5. Select Network Settings... on Printer Settings menu.

    The Confirm Printer Password screen appears.

    For more on the password, refer to Administrator Password.

    Note

    • Clicking the icon allows you to perform/change settings.
  6. Enter password and click OK.

    The Network Settings screen appears.

  7. Perform/change settings.

    You can switch the screen between IPv4 and IPv6. Click the tab to switch the protocol.

    • IPv4/IPv6 settings

      figure: Network Settings (Wireless LAN) screen
      1. Network Type:

        Select the wireless LAN mode.

        Infrastructure
        Connects the printer to the wireless LAN with a wireless router.
        Direct
        Connects the printer to wireless communication devices (smartphone or tablet) without a wireless router.

        Note

        • If Direct is selected, the Search... button is displayed in a gray out status.

          In addition, you cannot connect to Internet from your computer depending on your operating environment.

      2. SSID:

        The network identifier (SSID) of the wireless LAN currently used is displayed.

        The identifier for Wireless Direct (SSID) appears while in Wireless Direct.

      3. Search...

        The Detected Wireless Routers screen is displayed to select a wireless router to connect to. For a wireless router already connected to the computer, Available is displayed on Communication Status.

        If you select a wireless router with Not Connected on Communication Status from the list, clicking Set displays the WPA/WPA2 or WEP setting screen for a wireless router.

      4. Encryption Type:

        Displays the encryption method used over the wireless LAN.

    • IPv4 settings

      Note

      • The setting items below are available only when Infrastructure is selected for Network Type:.

        If Direct is selected, the setting items below are displayed in a gray out status.

      figure: Network Settings (Wireless LAN) screen
      1. Use IPv4 address

        Always selected. (displayed in a gray out state)

      2. Get IP address automatically

        Select this option to use an IP address automatically assigned by a DHCP server. DHCP server functionality must be enabled on your router.

      3. Use next IP address

        Select this option if no DHCP server functionality is available in your setup where you use the printer, or you want to use a fixed IP address.

        Enter the IP address, subnet mask, and default gateway.

    • IPv6 settings

      Note

      • If USB is selected from the pulldown menu on the toolbar, you cannot perform IPv6 settings.
      • The setting items below are available only when Infrastructure is selected for Network Type:.

        If Direct is selected, the setting items below are displayed in a gray out status.

      figure: Network Settings (Wireless LAN) screen
      1. Use IPv6 address

        Select when you use the printer with IPv6 environment.

      2. Use Stateless Address:

        Select when you use an IP address assigned automatically. Use a router compatible with IPv6.

        Note

        • This setting item is not available depending on the printer you are using.
      3. Use Manual Address:

        Select this option if no DHCP server functionality is available in your setup where you use the printer, or you want to use a fixed IP address.

        Enter the IP address and IP address prefix length.

        Note

        • This setting item is not available depending on the printer you are using.
      4. Use DHCPv6:

        Select when you obtain an IP address using DHCPv6.

        Note

        • This setting item is not available depending on the printer you are using.
  8. Click Set.